1963 Chevrolet C10

1963 Chevrolet C10 Pickup

For consignment, a consignor performed frame off build completed on a very utilitarian 1963 Chevrolet C10 pickup with about 400 miles logged since completion. Purchased by our consignor in 2019, the overall looks of the factory design have been retained but now with a black out treatment for the chrome, some new glass, a built to the hilt big block V8 and a strengthenedframe. It sports a custom laid out dash, a Speedway 22 circuit wiring harness, and snappy interior, along with a beautiful oak lined bed. Oh and I almost forgot to mention thecalming sea of turquoise paint that is 3 coats of base and clear.

Exterior
For 1963 the \"jet pod\" eyebrows are now gone, and the hood now is simplified yet still upstanding with turn signals and dual intake vents. Just below is the original restored to perfection single LED headlight equipped egg crate grille bordered below by a large and in charge bumper. We note all of the chrome and stainless has been powder coated black, adding a menacing aura to this hauler. Moving back, we note all straight steel for the body and bed panels that have been bathed in the deep end of the pool Sherman Williams Crystal Turquoise with 3 coats of color and 3 coats of clear to provide the mirror-like shine. Overall the gaps are well minded, the powder coated black trimmings are nicely redone, and all new glass with the exception of the wing vents is new. A few chips, touchups, inclusions and slight scratches are noted in the finish, but one must really look to see them. High above the fenders is now a custom cowl induction hood with black vent plates inserted on the tops and side. Within the well restored bed hides a Monster Liner coated oak bed floor with more liner coating on the sides and expanded wheel tubs. The rear of this truck remains basic and simple, just the way a truck should be with its black embossed Chevrolet tailgate, small blue dot equipped tail lights flank the sides of the gate and a custom roll pan below. Nice 15-inch glossy black steel wheels with shiny polished dog dish caps are all around wrapped in 205/75R15 blackwall rubber up front and 29x18.5-15\'s in the rear.

Interior
A swing of the double hulled door and we are greeted with black painted ribbed steel housing a smooth black vinyl insert with the crankand door handle within this field. A custom black vinyl Snowden bench seat with little to no wear stretches from door to door. It comes to us with a diamond pleating on the inserts, smooth body hugging bolsters and integral aluminum cup holders as well as Retro-Belt 4 point safety harnesses. An all steel black Monster Liner coated twin eyebrow designed dash is fronted by a custom billet steering wheel atop a new adjustable column and in front of the driver is the full monty of black face Dolphin gauges within a polished and ribbed bezel. Moving down the line we see black knobs and pulls below and in the center are the original heater and temp levers, and an aftermarket AM/FM radio with 300 watt 6x9 speakers and a Vintage AC/heater unit mounted just below. Lush black carpeting is flooding the floors all the while holding a custom made shifter on the hump and above is a really snappy ribbed metal roof in more black. Our consignor notes that during the build the entire cab was coated in Monster Liner then covered with Dynamat to keep road noise and heat to a minimum.

Drivetrain
Underneath the hood within the engine bay is a consignor-stated 496ci V8 that has been tapped for 4 bolt mains and was assembled by Mike Rogers Performance in Ivyland, PA using all ARP fasteners. This mill is estimated to make 625-650hpas per our consignor and that is thanks in part to the Liberty bottom end and AFR aluminum cylinder heads which are oval port 290cc units. The mill was then fitted with a Dennis Straub custom hydraulic roller cam with 302 degrees of duration and .600 lift. Howards roller lifters and roller rockers were also added and MSD is in charge of ignition with a Pro-Billet distributor, Blaster 2 coil and MSD ignition box. A 850cfmQuickFuel carburetor sends fuel and air into the engine via an Edelrbcok intake manifold and Hedman headers with 3\" Black Widow exhaust and WidowMaker mufflers are on for the huge exhale. A rebuilt by Trans Specialties in Aston, PA 3-speed TH350 automatic transmission with a Trans Specialties 2800-3200rpm stall converter sends power back to the Ford 9\" 4.11 geared rear axle with 31 spline axles and Yukon bearings. A CVF Racing serpentine belt drive system is on the front of the block and an aluminum radiator with a custom shroud and a Spahl electric puller fan keeps things nice and cool.

Undercarriage
Well done underneath with a sturdy black powder coated frame that has been customized and strengthened to withstand the rigors the big block mill produces. In front we see an all new independent coil spring suspension with new control arms, sway bar,

Read More

Read Less